Wurkkos TS25 4000lm Powerful Quad TIR Optic 8 Multi Color Aux LED 21700 USB-C Color Changing EDC Flashlight Torch

Operation Instructions

*Quick Start
-After putting a battery in the light and tightening the parts together, the light should quickly blink once

to confirm it has power and is now operational. After that, basic usage is simple:
Click to turn the light on or another click to turn it off.
- Hold the button to change brightness.
- Release and hold again to change brightness the other way.
-When Off, 7 quick clicks to change the Aux LEDs mode, cycle from-Rainbow(changes colors in order)

-->Voltage color display(changes color based on voltage)-->red color-->green color-->blue color-->off-->Rainbow
-Charge&Reverse Charging: Max input/output 5V3A with USB C Rechargeable port.
When charging: power indicator flash blue and turns to blue after full.
Reverse Charging: Power indicator turns blue , while the indicator flash blue, means low battery.
Power indicator on side switch shows 5 seconds after turn on, power enough(green color), low power(red color),

Very low (flashing red) That is all the user needs to know for basic use, but there are many more modes and features

available for people who want more.

Before reading the rest of this manual, it is recommended that users look at the Anduril UI diagram(s),

which should be provided along with the flashlight.

*Button presses
Button presses are abbreviated using a simple notation:
- 1C: One click. Press and then quickly release the button.
- 1H: Hold. Press the button, but keep holding it.
- 2C: Two clicks. Press and release quickly, twice.
- 2H: Click, hold. Click two times, but hold the second press.
- 3C: Three clicks. Press and release quickly, three times.
- 3H: Click, click, hold. Click three times, but hold the final press.
The same pattern is used with higher numbers too. For example, 10C means ten clicks... and

10H means ten clicks but hold the final press.
Simple UI Diagram Not everything is covered in the diagram, please read the text.

Simple UI

Simple UI Diagram Not everything is covered in the diagram, please read the text.
Simple UI
By default, the light uses a simple UI. This is useful if you lend the light to someone else, or if you

just don't want to bother with any crazy disco modes.
Simple UI has all the basic functions needed to work as a flashlight, but the minimum and
maximum brightness are limited to make it safer, and any complex or advanced functions are blocked.

Functions available in Simple UI include:
- 1C: On / off
- 1H: Ramp up (or down, if button was released less than a second ago)
- 2H: If light is on : ramp down
If light is off: momentary high mode
- 2C: Double click to go to / from highest safe level
- 4C: Lockout mode.

Some other modes and functions are available too. When the light is off, these are the options:
- 3C: Battery check mode. (displays voltage once, then turns off)
- 4C: Lockout mode.
- 10H: Switch to Advanced UI.
- 15C or more: Version check.
-7H:Aux LED mode adjust

In Lockout mode with Simple UI, there are a few functions:
- 1H: Momentary moon
- 2H: Momentary low
- 4C: Unlock and turn on
- 4H: Unlock and turn on at low level
- 5C: Unlock and turn on at high level

To change between Simple UI and Advanced UI, turn the light off and then do one of these:
In Simple UI:
- 10H: Go to Advanced UI.
In Advanced UI:
- 10C: Go to Simple UI.
- 10H: Configure Simple UI.

If you get lost, or if you want to auto-calibrate the temperature sensor, do a Factory Reset.

The process for this is:
- Loosen body tube
- Hold button
- Tighten body tube
- Keep holding button for about 4s

The light should flicker while getting brighter, then briefly burst to full power. Hold until it reaches

full power to do a reset, or let go of the button early to abort.